712 page 93 specifications are subject to change without notice ?00 9 teledyne relays www.teledynerelays.com 712/0909/q3 centigrid ? and to-5 series 712 commercial to-5 relays dpdt description the to-5 relay, originally conceived and developed by teledyne, has become one of the industry standards for low-lev el switching from dry circuit to 1 ampere. designed for high-density pc board mounting, the series 712 relays are some of the most versatile ultraminiature relays available because of their small size and low coil power dissipation. the following unique construction features and manufacturing techniques provide excellent resistance to environmental extremes and overall high reliability: ? all welded construction. ? unique uni-frame design providing high magnetic efficiency and mechanical rigidity. ? high force/mass ratios for resistance to shock and vibration. ? advanced cleaning techniques provide maximum assurance of internal cleanliness. ? precious metal alloy contact material with gold plating assures excellent high current and dry circuit switching capabilities. the series 712d relay has an internal discrete silicon diode for coil transient suppression. the hybrid series 712tn relay has an internal silicon diode and transistor driver. the integrated packaging of the relay with its associated semiconductor devices greatly reduces pc board floor space requirements as well as component installation costs. by virtue of its inherently low intercontact capacitance and contact circuit losses, the 712 has proven to be excellent ultraminiature rf switch for frequency ranges well into the uhf spectrum. a typical rf application for the to-5 relay is in handheld radio transceivers, wherein the combined features of good rf performance, small size, low coil power dissipation and high reliability make it a preferred method of transmit-receive switching (see figure 1). internal construction upper stationary contact lower stationary contact uni-frame armature moving contact series designation relay type 712 dpdt basic relay 712d dpdt relay with internal diode for coil transient suppression 712tn dpdt relay with internal transistor driver and coil transient suppression diode environmental and physical specifications temperature (ambient) storage C5? to +125 operating C5? to +85 vibration (general note 1) 10 gs to 500 hz shock (general note 1) 30 gs, 6 msec, half-sine enclosure hermetically sealed weight 0.09 oz. (2.6g) max.
?009 teledyne relays specifications are subject to change without notice 712 page 94 www.teledynerelays.com 712/0909/q3 centigrid ? and to-5 0 .1 .2 .3 .4 10 20 30 40 50 60 70 .01 0.5 .1 .5 1.0 frequency (ghz) figure 1 typical rf performance 1.92 1.22 1.07 1.02 1.01 1.00 1.00 vswr 300 250 200 150 100 50 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 load current (amps dc) figure 2 typical dc cont act rating (resistive) load vol tag e (vdc) db return loss (vswr) insertion loss isolation across cont act s isolation across poles series 712 general electrical specifications (@25) (notes 2 & 3) detailed electrical specifications (@25) (note 3) contact arrangement 2 form c (dpdt) rated duty continuous contact resistance 0.15 ohm max. before life; 0.25 ohm max. after life at 1a/28vdc (measured 1/8" from header) contact load ratings (dc) (see fig. 2 for other dc resistive voltage/current ratings) resistive: 1 amp/28vdc inductive: 200 ma/28vdc (320 mh) lamp: 100 ma/28vdc low level: 10 to 50 ?/10 to 50mv contact load ratings (ac) resistive: 250 ma/115vac, 60 and 400 hz (case not grounded) 100 ma/115vac, 60 and 400 hz (case grounded) contact life ratings 10,000,000 cycles (typical) at low level 1,000,000 cycles (typical) at 0.5a/28vdc resistive 100,000 cycles min. at all other loads specified above contact overload rating 2a/28vdc resistive (100 cycles min.) contact carry rating contact factory coil operating power 450 milliwatts typical at nominal rated voltage operate time 4.0 msec max. at nominal rated coil voltage release time 712: 3.0 msec max. 712d, 712tn: 6.0 msec max. intercontact capacitance 0.4 pf typical insulation resistance 1,000 megohms min. between mutually isolated terminals dielectric strength atmospheric pressure: 350 vrms/60hz negative coil transient (vdc) 712d, 712tn 2.0 max diode p.i.v. (vdc) 712d, 712tn 60 min. 712tn transistor characteristics base voltage to turn off (vdc) 0.3 min emitter-base breakdown voltage (bv ebo ) (vdc) 6.0 min collector-base breakdown voltage (bv cbo ) (@25 & lc = 100 ?) (vdc) 60 min performance curves (note 2) base part numbers (see note 8 for full p/n example) 712-5 712d-5 712tn-5 712-6 712d-6 712tn-6 712-9 712d-9 712tn-9 712-12 712d-12 712tn-12 712-18 712d-18 712tn-18 712-26 712d-26 712tn-26 coil voltage (vdc) nom. 5.0 6.0 9.0 12.0 18.0 26.5 max. 5.8 8.0 12.0 16.0 24.0 32.0 coil resistance (ohms ?0% @25? (712tn: see note 4) 50 98 220 390 880 1560 pick-up voltage (vdc, max.) pulse operated 3.6 4.2 6.5 8.4 13.0 17.0 712tn base current to turn on (madc, min.) 3.00 2.04 1.36 1.03 0.68 0.50
712 page 95 specifications are subject to change without notice ?00 9 teledyne relays www.teledynerelays.com 712/0909/q3 centigrid ? and to-5 10 1 2 3 4 5 6 7 8 9 dimensions are shown in inches (millimeters) .370 (9.40) dia. max. .335 (8.51) dia. max. .275 (6.99) max. +.002 (.05) .017 (.43) C001 (.03) dia. transistor base connection for 712tn only wire lead: .75 (19.05) min. terminal locations and pin numbering (ref. only) (viewed from terminals) case detail .035 (.89) .010 (0.25) .031 (.79) .003 (0.08) 36 3 typ. .200 (5.08) .010 (.25) dia. 712 712d schematics are viewed from terminals 712tn series 712 outline dimensions schematic diagram general notes 1. relay contacts will exhibit no chatter in excess of 10 sec or transfer in excess of 1 ?ec. 2. ypical characteristics are based on available data and are best estimates. no on-going verification tests are performed. 3. unless otherwise specified, parameters are initial values. 4. for reference only. coil resistance not directly measurable on 712tn relays. 5 . circuit is typical for all series 712tn. values shown are for 712tn-5 relay and apply for full temperature range. limit base-emitter current to 15 madc 6 . the slash and characters appearing after the slash are not marked on the relay. 7 . unless otherwise specified, relays will be supplied with either gold-plated or solder-coated leads. 8. vcc vr notes: logic 1 activates the rela y. logic 0 de-activates the rela y. vcc = logic bias po wer . vr = coil energization voltage. pin 10 pin 9 pin 1 logic element 1 = 0.50 to 3.00ma 0 = 0.3vdc min. typical logic interface (see note 5) te l edyne part numbering system f or commercial relays 712 x m - 26 / s q pad option (see appendix) relay series optional ground pin (see appendix ) coil v oltage q= solder coated leads g= gold plated leads (notes 6 and 7) s= 0.187" leads (note 6)
pad designation and bottom view dimensions height for use with the following: dim. h max. m4 pad for to-5 er411t er412, er412d, er412dd .295 (7.49) 712, 712d, 712tn, rf300, rf310, rf320 .300 (7.62) er420, er422d, er420dd, 421, er421d, er421dd, er422, er422d, er422dd, 722, 722d, rf341 .305 (7.75) er431t, er432t, er432, er432d, er432dd .400 (10.16) 732, 732d, 732tn, rf303, rf313, rf323 .410 (10.41) rf312 .350 (8.89) m4 pad for to-5 er411, er411d, er411dd .295 (7.49) er431, er431d, er431dd .400 (10.16) rf311 .300 (7.62) rf331 .410 (10.41) m4 pad for centigrid ? 172, 172d .305 (7.75) er114, er114d, er114dd, j114, j114d, j114dd .300 (7.62) er134, er134d, er134dd, j134, j134d, j134dd .400 (10.16) rf100 .315 (8.00) rf103 .420 (10.67) m9 pad for centigrid ? 122c, a152 .320 (8.13) er116c, j116c .300 (7.62) er136c, j136c .400 (10.16) rf180 .325 (8.25) a150 .305 (7.75) notes: 1. spacer pad material: polyester lm. 2. to specify an m4 or m9 spacer pad, refer to the mounting variants portion of the part numbering example in the applicable datasheet. 3. dimensions are in inches (mm). 4. unless otherwise speci ed, tolerance is .010 (.25). 5. add 10 m to the contact resistance show in the datasheet. 6. add 0.01 oz. (0.25 g) to the weight of the relay assembly shown in the datasheet. ?.150 [3.81] (ref) dim h max dim h max dim h max .156 [3.96] (ref) .256 [6.5] (ref) dim h max appendix a: spacer pads ? 2008 teledyne relays specifications subject to change without notice
pad designation and bottom view dimensions height for use with the following: dim. h max. m pad 5/ 6/ er411t, j411t, er412, er412d er412dd, j412, j412d, j412dd er412t, j412t .388 (9.86) 712, 712d, 712tn .393 (9.99) er431t, j431t, er432, er432d er432dd, j432, j432d, j432dd er432t, j432t .493 (12.52) 732, 732d, 732tn .503 (12.78) er420, j420, er420d, j420d er420dd, j420dd, er421, j421 er421d, j421d, er421dd j422d, er422dd, j422dd, 722 .398 (10.11) m2 pad 7/ 8/ er411t er412, er412d, er412dd j412, j412d, j412dd .441 (11.20) 712, 712d .451 (11.46) er421, er421d, er421dd 722, 732d .451 (11.46) er431t er432, er432d, er432dd .546 (13.87) 732, 732d .556 (14.12) m3 pad 5/ 6/ 9/ er411, er411d, er411dd er411tx er412x, er412dx, er412ddx er412tx .388 (9.86) 712x, 712dx, 712tnx .393 (9.99) er420x, er420dx, er420ddx er421x, er421dx, er421ddx er422x, er422dx er422ddx, 722x, 722ddx .398 (10.11) er431, er431d, er431dd er431tx er432x, er432dx, er432ddx er432tx .493 (12.52) 732x, 732dx, 732tnx .503 (12.78) notes: 1. spreader pad material: diallyl phthalate. 2. to specify an m, m2 or m3 spreader pad, refer to the mounting variants portion of the part number example in the applicable datasheet. 3. dimensions are in inches (mm). 4. unless otherwise speci ed, tolerance is .010 (0.25). 5/. add 25 m to the contact resistance shown in the datasheet. 6/. add .01 oz. (0.25 g) to the weight of the relay assembly shown in the datasheet. 7/. add 50 m to the contact resistance shown in the datasheet. 8/. add 0.025 oz (0.71 g) to the weight of the relay assembly shown in the datasheet. 9/. m3 pad to be used only when the relay has a center pin (e.g. er411m3-12a, 722xm3-26.) .370 [9.4] max sq .150 [3.81] .100 [2.54] .200 [5.08] .300 [7.62] .100 [2.54] dim h max .370 [9.4] min .014 [0.36] (ref) .390 [9.91] sq .300 [7.62] .100 [2.54] .300 [7.62] .100 [2.54] .150 [3.81] .150 [3.81] .130 [3.3] dim h max .370 [9.4] max sq .150 [3.81] .100 [2.54] .200 [5.08] .300 [7.62] .100 [2.54] dim h max .370 [9.4] min .014 [0.36] (ref) appendix a: spreader pads (800) 284-7007 ? www.teledynerelays.com +44 (0) 1236 453124 ? www.teledyne-europe.com ? 2008 teledyne relays
.100 [2.54] .100 [2.54] .100 [2.54] "y" position "z" position .100 [2.54] .100 [2.54] .100 [2.54] "w" position "u" position (er116c and er136c only) "x" position "z" position "y" position .050 [1.27] 36 3 ?.200 [?5.08] "z" position "y" position "x" position 45 3 "z" position "y" position ?.200 [?5.08] centigrid? relays: rf100, rf103, er114, er134, 172 centigrid? relays: rf180, er116c, 122c, er136c to-5 relays: er411t, er412, er412t, er420, er421, er422, er431t, er432, er432t, 712, 712tn, 400h, 400k, 400v, rf300, rf303, rf341, rf312, rf310, rf313, rf320, rf323 to-5 relays: er411, er431, rf311, rf331 notes 1. terminal views shown 2. dimensions are in inches (mm) 3. tolerances: .010 (.25) unless otherwise speci ed 4. ground pin positions are within .015 (0.38) dia. of true position 5. ground pin head dia., 0.035 (0.89) ref: height 0.010 (0.25) ref. 6. lead dia. 0.017 (0.43) nom. indicates ground pin position indicates glass insulated lead position indicates ground pin or lead position depending on relay type appendix a: ground pin positions ? 2008 teledyne relays specifications subject to change without notice
|
